DreamMaker 3D 3.3.6

The stylish and smart 3D printer evolved to be the most reliable and user friendly choice!

By GaryStadter
#3274
so, there is a chance I might possibly be the last individual to have received an Overlord Pro from the KickStarter campaign that hasn't unboxed yet.
I'm about to walk downstairs and unbox it and begin setup, but I thought I would take a gander at what developments had occurred across some of the more busy discussions in the community. ......oh wow ...some folks opening 3D hubs with theirs, others using lots and lots of expletives and describing resulting hair loss over their troubles with theirs.
to my question..... Has anyone, by rare chance, maintained any type of a "new user" guide that has included all or nearly all of the lessons learned to date? I'll put in the time to read through so many threads as I need to, but felt silly not asking the question, especially if someone has, in fact, gone to the effort of gathering up folks' experiences into one location. thanks
By RichardSu
#3277
Hi Gary,

Check out the below links, Hope it could help:

1) Unboxing the Overlord: https://www.youtube.com/watch?v=trqqPcXwB3M
2) Starting up wizard: https://www.youtube.com/watch?v=prZV5xkAC5w
3) Auto Leveling: https://www.youtube.com/watch?v=6nH8dSHQP_E
4) Manual leveling: https://www.youtube.com/watch?v=STSryjBD_ok
5) Apply glue stick: https://www.youtube.com/watch?v=od74l3tjDIw
6) Reload the material: https://www.youtube.com/watch?v=oMilEXvplPg
7) Power Failure: https://www.youtube.com/watch?v=MbWFuXCO0-4
8) Remove broken PLA in the tube: https://www.youtube.com/watch?v=mX0pX4c6DOQ
9) Clean the nozzle: https://www.youtube.com/watch?v=oWODdAn1t40
10) Clean the extruder: https://www.youtube.com/watch?v=0fkU-ByqNIQ
11) Adjust the height of build plate:https://www.youtube.com/watch?v=9ITzVDe9UKg
12) Replace the nozzle: https://www.youtube.com/watch?v=J7UMCZzuqwQ
By GaryStadter
#3278
RichardSu wrote:Hi Gary,

Check out the below links, Hope it could help:

1) Unboxing the Overlord: https://www.youtube.com/watch?v=trqqPcXwB3M
2) Starting up wizard: https://www.youtube.com/watch?v=prZV5xkAC5w
3) Auto Leveling: https://www.youtube.com/watch?v=6nH8dSHQP_E
4) Manual leveling: https://www.youtube.com/watch?v=STSryjBD_ok
5) Apply glue stick: https://www.youtube.com/watch?v=od74l3tjDIw
6) Reload the material: https://www.youtube.com/watch?v=oMilEXvplPg
7) Power Failure: https://www.youtube.com/watch?v=MbWFuXCO0-4
8) Remove broken PLA in the tube: https://www.youtube.com/watch?v=mX0pX4c6DOQ
9) Clean the nozzle: https://www.youtube.com/watch?v=oWODdAn1t40
10) Clean the extruder: https://www.youtube.com/watch?v=0fkU-ByqNIQ
11) Adjust the height of build plate:https://www.youtube.com/watch?v=9ITzVDe9UKg
12) Replace the nozzle: https://www.youtube.com/watch?v=J7UMCZzuqwQ


TY, Richard. No doubt whatsoever that you've just save me a LOT of time :D !
By RichardSu
#3281
Any time! :D I hope you could share your experience during your printing on this forum, also, any questions you could ask directly here and we gonna try our best to help you figure it out. :D

Thanks,
Richard.

Start your 3D printing journey